SIPLUS LOGO! 电源

发布日期：2017-06-07 14:02:25　　浏览量：

Overview

注意： SIPLUS extreme 产品基于西门子工业标准产品。此处列出的内容来自相关的标准产品。添加特定 SIPLUS extreme 设备信息

SIPLUS LOGO! 电源 1.3 A
订货号	6AG1 931-1SH02-2AA0
订货号基于	6EP1 331-1SH02
环境温度范围	-25 °C - +70 °C
敷形涂层	印刷电路板和电子元件的涂层
技术数据	除环境条件外，也同样适用标准产品的技术数据。
环境条件
相对湿度	5 ... 100 % 允许冷凝
生物活性物质	符合 EN 60721-3-3 标准，3B2 级霉菌和真菌孢子（动物群除外）
化学活性物质	符合 EN 60721-3-3 标准，3C4 级，包括盐雾和 ISA –S71.04 严重级别 G1；G2；G3；GX ¹⁾²⁾
机械活性物质	符合标准 EN 60721-3-3，Class 3S4，包括导电砂/尘 ²⁾
气压（取决于最高指定的最高正温度范围）	1080 ... 795 hPa (-1000 ...+2000 m）参见环境温度范围 795 ... 658 hPa (+2000 ...+3500 m）降容 10 K 658 ... 540 hPa (+3500 ...+5000 m）降容 20 K

1) ISA-S71.04 严重级别 GX：长期负载：SO2 < 4.8 ppm; H2S < 9.9 ppm; Cl < 0.2 ppm; HCl < 0.66 ppm; HF < 0.12 ppm; NH < 49 ppm; O3 < 0.1 ppm; NOX < 5.2 ppm

阈值/限值（最长 30 分钟/d）：SO2 < 17.8 ppm; H2S < 49.7 ppm; Cl < 1.0 ppm; HCl < 3.3 ppm; HF < 2.4 ppm; NH < 247 ppm; O3 < 1.0 ppm; NOX < 10.4 ppm

2) 在含有腐蚀性气体的环境中工作时，必须将提供的插头盖盖在未使用的接口上！

关于 SIPLUS 技术文档，可访问网址：

http://www.siemens.de/siplus-extreme

Area of application

SIPLUS LOGO! 电源在设计和功能方面与 SIPLUS LOGO! 逻辑模块最佳匹配；输入范围广：85 V 至 264 V 交流，带有用于安装在内置小型配电盘中的选件，它们可以在低端性能范围以及扩展的工作温度范围（-25 至 +70 °C）中普遍使用。

Technical Specifications

订货号	6EP1 331-1SH02
输入	单相交流电源
额定电压 U_in_rated	100 ... 240 V AC 宽范围输入
电压范围	85 ... 264 V AC
过压电阻	2.3 x V_{in rated}, 1.3 ms
电源缓冲，I_out rated 时	> 40 ms，U_in = 187 V 时
额定线路频率，额定线路频率范围	50/60 Hz; 47 ... 63 Hz
额定电流 I_in_rated	0.7-0.35 A
接通电流限制 (+25 °C)	< 35 A
I²t	< 0.8 A²s
集成输入熔断器	内部
在电源电缆中推荐使用小型断路器 (IEC 898)	16A以上，特性曲线B或者10A以上，特性曲线C
输出	可控，隔离直流电压
额定电压 U_输入_额定	24 V DC
总公差	±3 %
静态电源补偿	约 0.1%
静态负载平衡	约 1.5%
残余纹波	< 200 mV_pp（典型值10 mV_pp）
脉冲尖峰（带宽约 20 MHz）	< 300 mV_pp（典型值20 mV_pp)
调节范围	22.2- 26.4 V
状态显示	绿色 LED，表示 24 V O.K.
开关动作	U_out无过冲 (软起动)
起动延时 / 电压上升	< 0.5 s/ 典型值15 ms
额定电流 I_out_rated	1.3 A
电流范围
电流范围最大为 +60 °C	0 - 1.3 A (高达 55 °C)
降容	-
并联增加功率	√，2 个装置
效率
效率，U_out_rated，I_{out rated}时	约 82%
功率损失，当 U_out _rated, I_{out rated} 时	约 7 W
闭环控制
动态电源补偿 (V_{in rated} ±15%)	< 0.2 % U_输出
动态负载补偿 (I_out: 50/100/50 %)	典型值±1.5 % U_输出 (I_out: 10/90/10 %)
负载阶跃调节时间
50 ～ 100%	典型值20 ms (10 到 90%)
100 ～ 50%	典型值20 ms (90 到 10%)
保护和监控
输出过电压保护	√，符合标准 EN 60950
电流限值	典型值2 A
短路保护	恒定电流特性
连续短路 RMS 电流	< 4 A
过载/短路指示	-
安全
主/次隔离	√，安全特低输出电压 U_out，符合 EN 60950 和 EN 50178
保护类别	类别 II（无 PE 导体）
漏电电流	-
安全认证	√；CB 方案
CE 标识	√
UL/cUL (CSA) 认证	cULus 认证 (UL 508, CSA C22.2 No. 107.1), File E197259; cURus 认证 (UL 60950, CSA C22.2 No. 60950), File E151273
防爆	ATEX EX II 3G Ex nA IIC T3
FM 认证	等级 I Div. 2 组 A, B, C, D T4
船级社认证	GL, ABS
防护等级 (EN 60529)	IP20
EMC
辐射干扰	EN 55022 Class B
供电谐波限制	不适用
抗扰度	EN 61000-6-2
运行数据
环境温度范围	-20 至 +55℃，自然对流
运输和存储温度	-40 ... +70 °C
湿度等级	气候等级为 3K3，符合标准 EN 60721，无冷凝
机械机构
连接
电源输入端 L、N、PE （直流输入：L+1、M1、PE）	1 个螺钉端子 (L, N)，每个用于 0.5 mm ...2.5 mm² 单芯/细股绞线
输出 +	2 个螺钉型端子，用于 0.5 - 2.5 mm²
输出 -	2 个螺钉型端子，用于 0.5 - 2.5 mm²
外形尺寸（宽 x 高 x 深），[mm]	54 x 90 x 55
重量，约	约 0.17 kg
安装	卡装到标准安装导轨 EN 60715 35x7.5/15
附件	-

Technical Specifications

Order number	6AG1331-1SH03-7AA0	6AG1332-1SH43-7AA0	6AG1332-1SH52-7AA0
Product	SIPLUS LOGO!Power	SIPLUS LOGO!Power	SIPLUS LOGO!Power
Power supply, type	24 V/1.3 A	24 V/2.5 A	24 V/4 A
Input
Input	1-phase AC or DC	1-phase AC or DC	1-phase AC or DC
Rated voltage ＆#118alue Vin rated	100 ... 240 V	100 ... 240 V	100 ... 240 V
Voltage range AC	85 ... 264 V	85 ... 264 V	85 ... 264 V
Input voltage
● for DC	110 ... 300 V	110 ... 300 V	110 ... 300 V
Wide-range input	Yes	Yes	Yes
Overvoltage resistance	2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.	40 ms; at Vin = 187 V	40 ms; at Vin = 187 V	40 ms; at Vin = 187 V
Rated line frequency	50 ... 60 Hz	50 ... 60 Hz	50 ... 60 Hz
Rated line range	47 ... 63 Hz	47 ... 63 Hz	47 ... 63 Hz
Input current
● at rated input voltage 120 V	0.7 A	1.22 A	1.95 A
● at rated input voltage 230 V	0.35 A	0.66 A	0.97 A
Switch-on current limiting (+25 °C), max.	25 A	46 A	30 A
I²t, max.	0.8 A²·s	3 A²·s	2.5 A²·s
Built-in incoming fuse	internal	internal	internal
Protection in the mains power input (IEC 898)	Recommended miniature circuit breaker: from 16 A characteristic B or from 10 A characteristic C	Recommended miniature circuit breaker: from 16 A characteristic B or from 10 A characteristic C	Recommended miniature circuit breaker: from 16 A characteristic B or from 10 A characteristic C
Output
Output	Controlled, isolated DC voltage	Controlled, isolated DC voltage	Controlled, isolated DC voltage
Rated voltage Vout DC	24 V	24 V	24 V
Total tolerance, static ±	3 %	3 %	3 %
Static mains compensation, approx.	0.1 %	0.1 %	0.1 %
Static load balancing, approx.	1.5 %	1.5 %	1.5 %
Residual ripple peak-peak, max.	200 mV	200 mV	200 mV
Residual ripple peak-peak, typ.	10 mV	10 mV	30 mV
Spikes peak-peak, max. (bandwidth: 20 MHz)	300 mV	300 mV	300 mV
Spikes peak-peak, typ. (bandwidth: 20 MHz)	20 mV	50 mV	60 mV
Adjustment range	22.2 ... 26.4 V	22.2 ... 26.4 V	22.2 ... 26.4 V
Product function Output voltage adjustable	Yes	Yes	Yes
Output voltage setting	via potentiometer	via potentiometer	via potentiometer
Status display	Green LED for output voltage OK	Green LED for output voltage OK	Green LED for output voltage OK
On/off behavior	No overshoot of Vout (soft start)	No overshoot of Vout (soft start)	No overshoot of Vout (soft start)
Startup delay, max.	0.5 s	0.5 s	0.5 s
Voltage rise, typ.	15 ms	10 ms	15 ms
Rated current ＆#118alue Iout rated	1.3 A	2.5 A	4 A
Current range	0 ... 1.3 A	0 ... 2.5 A	0 ... 4 A
● Note	+55 ... +70 °C: Derating 2%/K	+55 ... +70 °C: Derating 2%/K	+55 ... +70 °C: Derating 2%/K
Active power supplied typical	30 W	60 W	96 W
Parallel switching for enhanced performance	Yes	Yes	Yes
Numbers of parallel switchable units for enhanced performance	2	2	2
Efficiency
Efficiency at Vout rated, Iout rated, approx.	85 %	88 %	89 %
Power loss at Vout rated, Iout rated, approx.	6 W	8 W	12 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max.	0.2 %	0.2 %	0.2 %
Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.	1 %	2 %	1.5 %
Load step setting time 10 to 90%, typ.	1 ms	1 ms	1 ms
Load step setting time 90 to 10%, typ.	1 ms	1 ms	1 ms
Protection and monitoring
Output overvoltage protection	Yes, according to EN 60950-1	Yes, according to EN 60950-1	Yes, according to EN 60950-1
Current limitation, typ.	1.7 A	3.3 A	5.2 A
Property of the output Short-circuit proof	Yes	Yes	Yes
Short-circuit protection	Constant current characteristic	Constant current characteristic	Constant current characteristic
Enduring short circuit current RMS ＆#118alue
● maximum	2.4 A	4.8 A	7.9 A
Overload/short-circuit indicator	-	-	-
Safety
Primary/secondary isolation	Yes	Yes	Yes
Galvanic isolation	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
Protection class	Class II (without protective conductor)	Class II (without protective conductor)	Class II (without protective conductor)
CE mark	Yes	Yes	Yes
UL/CSA approval	No	No	No
Degree of protection (EN 60529)	IP20	IP20	IP20
EMC
Emitted interference	EN 55022 Class B	EN 55022 Class B	EN 55022 Class B
Supply harmonics limitation	not applicable	not applicable	EN 61000-3-2
Noise immunity	EN 61000-6-2	EN 61000-6-2	EN 61000-6-2
Operating data
Ambient temperature
● during operation	-40 ... +70 °C	-40 ... +70 °C	-40 ... +70 °C
— Note	with natural convection	with natural convection	with natural convection
● during transport	-40 ... +85 °C	-40 ... +85 °C	-40 ... +85 °C
● during storage	-40 ... +85 °C	-40 ... +85 °C	-40 ... +85 °C
Ambient condition relating to ambient temperature - air pressure - installation altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m); Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m); Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m); Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m); Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m); Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m); Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity with condensation maximum	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)
Resistance to biologically active substances conformity acc. to EN 60721-3-3	Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation!
Resistance to chemically active substances conformity acc. to EN 60721-3-3	Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
Resistance to mechanically active substances conformity acc. to EN 60721-3-3	Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Mechanics
Connection technology	screw-type terminals	screw-type terminals	screw-type terminals
Connections
● Supply input	L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded	L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded	L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded
● Output	+, -: 2 screw terminals each for 0.5 ... 2.5 mm²	+, -: 2 screw terminals each for 0.5 ... 2.5 mm²	+, -: 2 screw terminals each for 0.5 ... 2.5 mm²
● Auxiliary	-	-	-
Width of the enclosure	54 mm	72 mm	90 mm
Height of the enclosure	90 mm	90 mm	90 mm
Depth of the enclosure	55 mm	55 mm	55 mm
Weight, approx.	0.17 kg	0.25 kg	0.34 kg
Product property of the enclosure housing for side-by-side mounting	Yes	Yes	Yes
Installation	Snaps onto DIN rail EN 60715 35x7.5/15	Snaps onto DIN rail EN 60715 35x7.5/15	Snaps onto DIN rail EN 60715 35x7.5/15
Other information	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

SIPLUS LOGO! 电源

上一篇：LOGO!Power 电源

下一篇：LOGO！连接

产品和服务

公司信息

联系我们